📞 01377 337172 ✉️ sales@fcmarine.co.uk
Mon–Fri: 09:00–17:00 (UK)

Marine power supplies and DC converters perform different jobs: some convert shore or generator AC into regulated DC, others convert one DC voltage to another, and dedicated DC-DC battery chargers control charging between battery banks. Mixing them up can cause equipment faults or battery damage.

Marine DC electrical system with chargers and DC-DC converter
Concept illustration of a vessel power system — not a wiring diagram.

1. AC-to-DC supplies, DC converters and chargers

An AC-to-DC power supply converts a suitable mains AC input into the DC voltage equipment requires. A regulated DC-to-DC converter changes one DC supply voltage to another; depending on its design it may step voltage down, up, or both. A DC-to-DC battery charger adds charging algorithms and controls appropriate to a secondary battery bank. A fixed-voltage supply must not be assumed suitable for charging batteries.

Marine AC-DC and DC-DC conversion comparison
Illustration comparing AC-DC charging and DC-DC conversion; exact topology varies by product.

2. What 12 V, 24 V and 28 V mean

Nominal 12 V and 24 V battery systems do not stay at precisely those voltages. Voltage varies with charge state and charging sources, so a connected device must tolerate the actual minimum and maximum voltage. A 28 V-rated equipment input may be intended for a nominal 24 V system under charging conditions, but it does not follow that every 28 V device or every 24 V supply is interchangeable. Verify the input-voltage range on the actual equipment label or manufacturer documentation.

For a 24 V vessel feeding a 12 V electronic device, choose a converter with an input range covering the vessel’s operating conditions and a regulated output within the load’s permitted tolerance. Do not use an unregulated voltage divider as an equipment power source.

3. Calculate continuous load and starting peaks

List every device on the intended supply and its continuous current, startup surge and duty cycle. For illustration, a 12 V rail supplying 3 A and 5 A devices requires at least 8 A before engineering margins and any starting peaks; its approximate output power at 12 V is 96 W. Input power will be higher than output power because the converter is not perfectly efficient.

Check the specified continuous rating at the installation temperature, any peak rating and whether a manufacturer’s thermal derating applies. Multiple devices powered by one converter can have simultaneous inrush requirements that exceed a simple running-current calculation.

4. Isolated versus non-isolated DC-DC equipment

An isolated converter separates the input and output circuits galvanically as defined by its design; a non-isolated model does not provide that separation. Selection depends on the vessel’s earthing, negative return, interference environment and manufacturer’s installation rules. Isolation is not a substitute for correctly designed protective earthing or suitable galvanic corrosion controls.

Victron’s Orion-Tr Smart documentation, for example, distinguishes isolated and non-isolated versions and publishes separate input ranges, continuous-current limits and output adjustment ranges. This illustrates why the specific variant must be checked rather than choosing by wattage alone. Manufacturer isolated-model specifications and non-isolated specifications.

5. Actual marine power equipment examples

SAILOR N163S marine AC-DC power supply product photograph
SAILOR N163S power supply photograph from the F&C Marine Media Library.

The SAILOR N163S is a legacy universal AC/DC supply. Its published datasheet specifies 110/127/220/237 V AC input, a 24 V DC unregulated output rated at 7 A, and automatic changeover from AC mains to an external 24 V DC source. It is therefore not an example of a tightly regulated 24 V DC supply, nor a universal replacement for a different unit. Confirm the equipment’s allowed supply range, AC input selection, connections and load against its technical manual.

SAILOR 6090 marine DC-DC power converter product photograph
SAILOR 6090 power converter product image.

For the SAILOR 6090 (part number 406090A-00500), the published installation data gives an operational input of 21–32 V DC, an output of 12.5 V DC ±5% and up to 8 A output current at 12.5 V. It is designed for specified SAILOR VHF applications, not as a universal 24 V-to-12 V converter. Verify the exact radio model, connections and installation instructions before ordering.

6. Battery charging is a separate design decision

CRISTEC DCPOWER Plus DC-DC battery charger product illustration
CRISTEC DCPOWER+ equipment illustration; select the exact charging model for the battery system.

Where the destination is a battery bank rather than a DC load, the system generally needs a compatible charging profile and protection coordination. A dedicated DC-DC charger can limit current and control charging between engine and auxiliary banks. Victron’s manufacturer documentation expressly distinguishes power-supply mode and battery-charger mode on products supporting both. A battery’s BMS protection and its required charge profile remain relevant even when a converter is marketed as lithium-compatible.

7. Installation and safety checklist

  • Input: confirm minimum/maximum supply voltage, polarity and expected transients
  • Output: confirm continuous current, surge load, voltage tolerance and ripple sensitivity
  • Protection: use correctly rated DC fuses or breakers and suitable conductor protection
  • Environment: follow mounting orientation, cooling clearances, ingress protection and temperature limits
  • Wiring: check both positive and return cable length, voltage drop, terminations and strain relief
  • Interference: keep sensitive GNSS, AIS, radio and NMEA electronics away from poorly routed power wiring; investigate conducted noise where performance is affected
  • Commissioning: measure output at the load during starting and maximum expected load, not only unloaded on a bench

8. Common faults and troubleshooting

Unexpected resets can arise from supply voltage dips, undersized cables, excessive startup current or converter overload. An overheating unit may be operating beyond its temperature-dependent continuous rating or may lack ventilation. Radio and GNSS interference can be linked to switching-noise coupling or poor cable routing, but should be tested rather than assumed. Repeated protective shutdown requires checking faults and loading, not bypassing protective devices.

9. Frequently asked questions

Can I run 12 V electronics from a 24 V boat?

Yes, with a suitable 24 V-to-12 V converter matched to the device’s actual allowable voltage, continuous current and surge requirements.

Can a 24 V power supply charge a 24 V battery?

Not automatically. Charging requires the appropriate charge voltage, current limiting and control profile. A fixed 24 V supply may be unsuitable for charging a nominal 24 V battery bank.

What is the difference between 24 V and 28 V equipment?

The numbers may describe nominal system voltage, regulated supply output or an equipment operating point. Only the specified allowable input range determines compatibility.

Should a converter have more power than the load?

It should be selected with suitable continuous capacity, thermal conditions and peak-load allowance according to the manufacturer. An arbitrary percentage margin is not a substitute for checking rated operating conditions.

10. F&C Marine equipment selection and support

To identify a replacement, send the existing unit’s part number, photographs of the label and terminals, input supply, required load voltage, running/peak current, available space and connected radio or navigation equipment. F&C Marine can review options, associated connectors, installation and functional checks. Request a quotation.

Related reading: Marine battery chargers, marine lithium batteries and marine solar charging.

References: Victron DC-DC operating modes; Victron isolated DC-DC specifications. Installation requirements are model-specific. Illustrations are educational rather than approved wiring plans.

Leave a Reply

Your email address will not be published. Required fields are marked *